HONEYWELL | UCN DCS Power Supply Unit
HONEYWELL ACX631 51198947100F Cherokee Power Supply
TDC3000 UCN HPM/APM/PM Cabinet Power Module · Redundant DCS Power Supply
Product Overview
The Honeywell ACX631 51198947100F is a Cherokee-manufactured AC/DC power supply dedicated for Honeywell TDC3000 UCN Universal Control Network cabinets, compatible with HPM, APM and PM controller racks. It supports wide-range AC input and 48V DC battery backup, integrates battery charging circuit and multi-channel regulated output for UCN controllers and backplane. It features LED status indicators for DC output, battery, fault/temp, AC input and charging. This is an obsolete legacy spare widely used in petrochemical, refining and power plant DCS maintenance replacement, FM approved Class I Div 2 hazardous location rated.

The suffix F represents revision F hardware version. It is commonly deployed in redundant power pair configuration for critical control cabinets to avoid single point power failure.
Part Number
ACX631 51198947100F
System Platform
TDC3000 UCN HPM/APM/PM
Input Range
85–264VAC 50/60Hz / 48VDC
Aux Output
6VAC @35mA Sync
Origin & Cert
USA, FM Class I Div 2
Key Features
Dual Input Source Support
Accept universal AC mains or 48V DC battery bank input, built-in charging circuit for 48V backup battery, ensures seamless transfer during mains outage.
Multi-Channel Regulated Output
Primary 25.25VDC for UCN controller backplane, plus 6VAC low-current output for line frequency synchronization of TDC3000 system.
Redundancy Ready Design
Designed for side-by-side redundant power installation in HPM/APM cabinets; hot swap replacement under paired redundant configuration with caution procedure.
Front Panel Diagnostic LEDs
Five status LEDs: DC Output, Battery, Fault/Temp, AC Input, Charging, for quick on-site troubleshooting without extra tools.
Hazardous Area Approval
FM approved Class I Division 2, T4 temperature rating, suitable for oil, gas, chemical and refinery explosive classification zones.
Legacy DCS Spare
Original production discontinued, only available as surplus/refurbished spare; no direct drop-in modern replacement for TDC3000 UCN rack.
Complete Protection
Overvoltage, overcurrent, short circuit and overtemperature protection, prevents cascading damage to expensive UCN controller boards.
Typical Applications
Power supply for Honeywell TDC3000 UCN distributed control system cabinets.
Oil Refinery DCS Control Room
Redundant power feeding HPM high-performance control cabinets for refining process control.
Petrochemical Plant Process Control
APM/PM cabinet power supply for reactor, distillation and pipeline control loops.
Power Plant Auxiliary DCS
TDC3000 UCN rack power for boiler, turbine and auxiliary system control.
Offshore Platform Control System
Battery-backed redundant power for critical UCN controllers on offshore installations.
Natural Gas Compression Station
Class I Div2 compliant power supply for gas pipeline and compressor control.
TDC3000 System Maintenance
Direct replacement for failed ACX631 power modules in existing UCN cabinets.
Frequently Asked Questions
Which cabinets can this PSU fit?
It is designed for Honeywell TDC3000 UCN HPM, APM and PM controller cabinets, not compatible with LCN or other series racks.
What is the difference between 51198947-100 and 51198947-100F?
F suffix denotes Revision F hardware PCB version; check original revision and component marking before replacement to match compatibility.
Can you replace it live while cabinet running?
Only allowed when redundant pair is installed; follow Honeywell lockout-tagout and hot-swap procedure, do not remove both PSUs at the same time.
Does it charge the 48V battery automatically?
Yes, built-in battery charging circuit, the front charging LED indicates charging status of the 48V backup battery bank.
Is there a new generation replacement?
No direct drop-in substitute; full migration from TDC3000 UCN to Honeywell Experion PKS is the long-term upgrade solution.
What to confirm before ordering?
Original part number & revision, cabinet type (HPM/APM/PM), redundant configuration, battery voltage and hazardous area certification requirement.